| |
|
1955-79 VW bus narrowed adjustable beams These beams are high quality and hand built in the USA.
Built for any year bus from 55-79 with several different types 2-5 inch's narrowed.
2,4,5 inch narrowed adjustable 1955-67 with polymolly bushings = 599.00
2,4,5 inch narrowed adjustable 1968-79 with polymolly bushings = 699.00
Add 125.00 for original needle bearings.
Narrowed tie rods are 85.00 a set for any year.
We also build completes front and back.
No modifications needed to install, these beams are ready to bolt up!
These beams are built using brand new machined steel and are GUARENTEED to the Original buyer for the life of the bus if any thing should go wrong send it back we will repair/replace and ship it back no charge!
Back to the top
|
|
|
| |
|
|
| |
All beams come with narrowed springs! |
|
|
| |
|
|
|
|
|
|
55-79 Air ride bus beam. 1400.00 with bags Wagenswest new air ride beams are 4 inches narrowed and utilize two 2500 pound Air Lift bags that sit inside the frame rails of the bus. The beam is designed to use the stock springs in both top and bottom tube, with the top spring being held by an adjuster and the bottom spring supported by the air bags. The ride height and air bag travel is dependant on the adjustable preload of the top spring. If you have any questions or are interested in ordering one of these beams please call or email Wagenswest 503-587-0700 parts@wagenswest.co
Back to the top
|
|
|
| |
|
|
| |
 |
|
| |
|
|
|
 |
|
55-67 air bag off set spring plates. 500.00 with bags These spring plates are built to be used just like the off set spring plates but with a twist. They also incorporate air bags in to the mix dubbing as your bottom air bag bracket, making it very simple to install air bags in the rear of your bus. They come with weld in top bag mounts.
Back to the top |
| |
|
|
| |
|
Wagenswest 55-79 Complete front ends Spindle to spindle or disk to disk Our complete front ends come with every thing in-between Adjustable narrowed beam 2,4,5. New center pin and pitman arm with damper. New shocks and remanufactured trailing arms. Narrowed tie rods and ends. Dropped spindles are 2.5 inch 3.5 inch 4 inch 5 inch and 6 inch. Optional bustang wide five brakes or Porsche 5 on 130, as well as a few other styles. Complete front ends come fully assembled and are shipped via truck freight shipping varies from 150.00 – 350.00 in the continental USA and 450.00 to 700.00 around the world. Call or email 503-587-0700 Parts@wagenswest.com
Back to the top |
|
|
| |
|
|
| |
|
|
Narrowed tie rods with ends 1955-79 narrowed bus tie rods can be ordered in custom lengths. Pair of Generic narrowed tie rods with ends = 85.00
Pair of German or equivalent narrowed tie rods with ends = 155.00
Back to the top |
|
|
|
| |
|
|
| |
|
|
|
|
| |
|
|
Original German VW bus leaf springs
Stock length = 150.00
Narrowed = 175.00
Back to the top
|
|
| |
|
|
|
|
|
Wagenswest (BEEF CAKE) bus beam adjusters, drop forged out of chromoly with big beefy teeth to insure a solid grip with no slip. These fit Volkswagen bus beams from 1955-1979 48.00 Each or 90.00 for two Back to the top |
|
|
|
|
|
|
| |
|
|
|
Wagenswest bus beam bushings 1964-79
100.00 a set of 4 with free shipping
Special blend polyurethane bus bushings
These bushing are made to fit 1964-67 and 1968-1979 as stock replacements or for narrowing.
We have many different variations to accommodate the different years and sizes for instance if you want to put 64-67 trailing arms in an early beam without removing the races these will do it and vice versa you name we make it.
Back to the top |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
68 – 79 Rebuilt ball joint bus trailing arms
$295.00 ( NO CORE CHARGE !! )
Rebuilt trailing arms come with new ball joints and are clean painted and ready to install
Back to the top |
| |
|
|
|
| |
|
|
|
|
New 1964-67 bus king pins !
Wagenswest now has affordable 64-67 bus king pins and they are very high quality!
Forged and CNC machined with hardened chromoly bearing surfaces.
Good king pins are a must have when rebuilding 64-67 VW bus front spindles.
For 169.00 you get a full set enough for one pair of spindles 2 top and 2 bottoms with 4 bushings.
If you need a piece by itself we can do that too.
Top king pin fits left or right = 49.00 comes with bushing
Bottom king pin fits left or right = 49.00 comes with bushing
Back to the top |
|
| |
 |
|
| |
|
|
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
|
|
Wagenswest Porsche conversion drops.
Custom built bus/Porsche 944 hybrids 2.5-6 inch drop 270.00 with your core spindles or 650.00 with out. We also do other combinations of spindles just call or email if you have an idea
503-587-0700.
Back to the top |
|
|
|
|
|
|
|
| |
1968-79 bus dropped spindles 2 1/2 inch dropped spindles
$415.00 ( NO CORE CHARGE !!! ) $270.00 with your core set up front. These dropped spindles have a 12 mm wheel base increase per side, and you may need to trim a small bit from your backing plate. Back to the top |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
Pre 67 bus dropped spindles $225.00 plus shipping. You ship us your spindles and we inspect for damage and reinforce them with gussets. Then we do a reverse taper to accommodate late model tie rods installed upside down to help clear your chassis, after that we reassemble them 3 ½ inches lower, install high quality seals, paint them and ship them back. This has proven to be a very popular service
Back to the top |
|
|
|
|
1955-67 Welded dropped spindles With a 4, 5, and 6 inch drop these are by far the best spindles you can buy for a Volkswagen bus. Built using special jigs these spindles keep all your stock tie rod geometry as well as maintaining all the original Bakelite pivot bushings.
4 inch will fit inside a 14 inch and bigger wheel. 5 inch will fit inside a 15 inch and bigger wheel. 6 inch will fit inside a 16 inch and bigger wheel.One more major benefit is that you can install these spindles with stock tie rods and ends so all you need is the spindles!!
3/8 track increase each side
These are 650.00 out rite or 375.00 with your core set.
Back to the top
|
|
| |
|
|
|
68-79 Bay window horse shoe plates. 155.00 A pair with bolts. These horse shoe plates lower the rear of your 68-79 bay window bus 3 ¼ inches while maintaining stock camber and leaving your spring plate in its original location. These plates also maintain the factory wheel base and do not push your wheels out.
Back to the top |
| |
|
|
|
|
|
|
68-79 4.5 inch drop plates.
Now you can finally just bolt up custom wheels on your bay bus with out any hassles no kidding these plates drop the back of your bus 4.5 inches and narrow it ¾ inch each side. 275.00 a set Back to the top |
|
|
|
| |
|
|
|
55-67 off set spring plates
200.00 With core or 295.00 out rite.
Off set spring plates enable you to lower the rear of your pre 1967 Volkswagen bus 3.5 inches by swapping the reduction gear transmission with a long axle type one or type three swing axle transmissions.
What you need to do the job
#1 A set of off set spring plates.
#2 a 68 bug swing axle transmission or a pre 67 type 3 transmission.
#3 brakes if you use the 68 bug transmission you can machine a set of pre 63 bus drums to fit over the bug brakes or if you use a type 3 you can buy wide five drums.
#4 A pair of emergency brake cable spacers.
You will also need to take the bus nose cone off of the bus trans and use it on the bug or type 3 transmission.
By far the easiest way to lower the back of your bus.
We also have several different types of brand spanking new made in the USA spring plates from off set to dog legged straight axle and IRS as well as adjustable.
|
New off set spring plates no core 295.00
New IRS spring plates are 225.00
New dog legged super slam straight axle plates 245.00
New adjustable off set spring plates 365.00
New adjustable IRS spring plates 295.00
New adjustable dog legged straight axle spring plates 320.00
Back to the top
|
|
|
|
|
 |
|
|
|
|
|
| |
|
| |
|
|
|
|
|
|
|
|
Bolt in type one IRS kit for your pre 67 bus
$375.00 ( NO CORE CHARGE !! ) $275.00 with your core spring plates.
This is a bolt in IRS kit that consist of bolt in trailing arm shackles, spring plates and spring plate spacers allowing you to bolt in type one IRS trailing arms axles and transmission.
Some trimming and drilling is required Back to the top |
| |
|
|
|
| |
|
| |
Wagenswest Return Policy
All sales are final. We will work with you if the part is not satisfactory or if it does not fit properly CALL US. All parts are guaranteed for the life of the vehicle to the original buyer against premature ware; if there is a problem send it back we will repair or replace it at no charge.
Back to the top Wagenswest home page |
Warning these are automobile parts designed for specific uses in automobiles only. The parts may be dangerous and may cause injury if used for any other purpose, or otherwise misused. They may also be dangerous and may cause injury if modified, redesigned or altered before use. Wagenswest will not assume any liability for and will not pay you for any injuries caused to you or others by any misuse, modification, redesign, or alteration of our products. These parts are not for use on public highways, off-road racing purposes only. Wagenswest will not be responsible for any incidental or consequential damage including direct or indirect labor, towing, lodging, garage, repair, medical or legal expense in any way attributable to the use of any item on this website, or to the delay or inconvenience caused by the necessity of replacing or repairing any such item.
|
|
|
| |
|
| |
